#============================================================================
# Example configuration script for Devuan guest installation.
#============================================================================
#
# To install uncomment the relevant options under either the network
# or CDROM install section in "AT INSTALLATION TIME" below.
#
# Once you have installed you should comment out the installation options again
# (or just delete them) and uncomment the options under "TO BOOT INSTALLED
# SYSTEM" instead.

#============================================================================
# AT INSTALLATION TIME
#============================================================================

#----------------------------------------------------------------------------
# Network install:
#----------------------------------------------------------------------------
#
# Download vmlinuz and initrd.gz from the same location as this file.
#
# e.g. depending on the architecture you wish to install:
#   http://http.mirrors.devuan.org/devuan/dists/stable/main/installer-amd64/current/images/netboot/xen/
# where XX is a country code, see http://www.devuan.org/mirror/list
# for a complete list of official mirrors. "stable" can be any distro
# name (e.g. squeeze, wheezy, jessie, stretch, testing, sid, unstable).
#
# Uncomment the "kernel" and "ramdisk" options and adjust the path to
# point to the downloaded files.

#kernel = "vmlinuz"
#ramdisk = "initrd.gz"

#----------------------------------------------------------------------------
# CDROM install:
#----------------------------------------------------------------------------
#
# Download an ISO image which supports installation under Xen. Typically these
# are the amd64+i386 multiarch images. e.g. those under:
#   http://cdimage.devuan.org/devuan-cd/current/multi-arch/
#
# Uncomment "bootloader" and the correct "bootloader_args" for the
# architecture you wish to install.
#
# Be sure to configure a CDROM device with the installation image in
# addition to your regular disk HDD in your disk stanza.
#
# e.g. for an ISO image:
#   file:/path/to/devuan-1.0.0-amd64-i386-netinst.iso,xvdd:cdrom,r
#    -or- if you have a phyiscal cdrom in your drive, phy:
#   phy:/dev/cdrom,xvdd:cdrom,r

#bootloader="pygrub"

# For i386:
#bootloader_args="--kernel=install.i386/xen/vmlinuz --ramdisk=install.i386/xen/initrd.gz"
# For amd64:
#bootloader_args="--kernel=install.amd/xen/vmlinuz --ramdisk=install.amd/xen/initrd.gz"

#----------------------------------------------------------------------------
# Installation options common to all methods
#----------------------------------------------------------------------------
#
# If you configure a vfb below then use "console=tty0" instead of
# "console=hvc0".
# 
# You can prepend your own command line options too

#extra = "debian-installer/exit/always_halt=true -- quiet console=hvc0"

#============================================================================
# TO BOOT INSTALLED SYSTEM
#
# Comment all of the above installation options and uncomment the
# below instead
#============================================================================

#bootloader="pygrub"

#============================================================================
# STANDARD OPTIONS
#============================================================================
#
# The following options are common to both installation time and normal booting.
# 
# Only a subset of the available options are included below.
# See /usr/share/doc/xen-utils-common/examples for full examples.

#----------------------------------------------------------------------------

# Initial memory allocation (in megabytes) for the new domain.
memory = 128

# A name for your domain. All domains must have different names.
name = "ExampleDomain"

# 128-bit UUID for the domain.  The default behavior is to generate a new UUID
# on each call to 'xm create'.
#uuid = "06ed00fe-1162-4fc4-b5d8-11993ee4a8b9"

# List of which CPUS this domain is allowed to use, default Xen picks
#cpus = ""         # leave to Xen to pick
#cpus = "0"        # all vcpus run on CPU0
#cpus = "0-3,5,^1" # run on cpus 0,2,3,5

# Number of Virtual CPUS to use, default is 1
#vcpus = 1

#----------------------------------------------------------------------------
# Define network interfaces.

# By default, no network interfaces are configured.  You may have one created
# with sensible defaults using an empty vif clause:
#
# vif = ['']
#
# or optionally override backend, bridge, ip, mac, script, type, or vifname:
#
# vif = ['mac=00:16:3e:00:00:11, bridge=xenbr0']
#
# or more than one interface may be configured:
#
# vif = ['', 'bridge=xenbr1']

vif = ['']

#----------------------------------------------------------------------------
# Define the disk devices you want the domain to have access to, and
# what you want them accessible as.
# Each disk entry is of the form phy:UNAME,DEV,MODE
# where UNAME is the device, DEV is the device name the domain will see,
# and MODE is r for read-only, w for read-write.
#
# NB: Only xvd devices are supported by the kernel in Debian Lenny and later.

disk = ['file:/path/to/disk.img,xvda,w']

#----------------------------------------------------------------------------
# Define frame buffer device.
#
# By default, no frame buffer device is configured.
#
# To create one using the SDL backend and sensible defaults:
#
# vfb = [ 'type=sdl' ]
#
# This uses environment variables XAUTHORITY and DISPLAY.  You
# can override that:
#
# vfb = [ 'type=sdl,xauthority=/home/bozo/.Xauthority,display=:1' ]
#
# To create one using the VNC backend and sensible defaults:
#
# vfb = [ 'type=vnc' ]
#
# The backend listens on 127.0.0.1 port 5900+N by default, where N is
# the domain ID.  You can override both address and N:
#
# vfb = [ 'type=vnc,vnclisten=127.0.0.1,vncdisplay=1' ]
#
# Or you can bind the first unused port above 5900:
#
# vfb = [ 'type=vnc,vnclisten=0.0.0.0,vnunused=1' ]
#
# You can override the password:
#
# vfb = [ 'type=vnc,vncpasswd=MYPASSWD' ]
#
# Empty password disables authentication.  Defaults to the vncpasswd
# configured in xend-config.sxp.